Tag Archives: Metal Morphous

Back from the Paint Shop! (November 2016)

I left the coupe with Ron Randall at Metal-Morphous in Connecticut on June 25.  It has been a very long four and a half months, but I am extremely happy with the results.  Ron and his crew did an amazing job aligning the doors and hood, sanding, sealing, and painting.  Here are just a few of the photos that Ron sent to me through the process, as well as some photos of my bring her home.

Body off the chassis and application of gelcoat.  Note the louvres I obtained for the side vents.

1-gel-coat5-louvres

Base coat of “Wimbledon White” applied.

6-paint-wimbledon-white

Tape over what will become the rally stripes.

7-paint8-paint

First coat of “Guardsman Blue”.

9-paint

Remove the tape, reveal the stripes, apply clear coat for shine..

10-paint

Polish, clear coat, polish, clear coat, and repeat many times for an even deeper shine.

 

Re-assemble body, doors and hood.

18-paint21-paint

In addition to body and paint, I asked Ron to install the headliner material for me (before putting the body back on the chassis), as well as the side windows (“side curtains”) because that went hand-in-hand with the final fitting of the doors.  I also had his guy install the windshield and gasket for me.

26-side-curtain

I arrive to pick up the coupe and I am ecstatic.  We go over the car.  Hard to see in these pics, but the hood scoops and rear spoiler are attached via metal screws.  Some guys prefer to use fiberglass to blend these pieces seamlessly into the shape of the body, but I prefer the screws for that “old school” feel and look.  (The original coupes were hammered out of metal and rivets.)  I ask Ron and Pedro to apply the race numbers for me.  (I will apply the sponsor decals later.  They are smaller and easier to handle.)

31-paint

At a rest stop in Connecticut.

35-paint

What it looks like when a 1965 Shelby Daytona Coupe tailgates you all the way from Connecticut to Pennsylvania.

36-paint

And finally at home.

37-paint

38-paint

 

Body Work (July 31 2016)

At the time of my last update I had just dropped off the Coupe at Metal Morphous (MM) in Connecticut.  Since then MM has provided me with weekly updates, and I was able to stop by last week while travelling in that vicinity.  MM is being very deliberate and methodical.  When sanding down the “seams”, they are careful to discover any air (or gas) pockets that may have developed in the original fiberglass mold process. MM advises that such pockets are typical, but that if you paint without filling them, they will later reveal themselves as defects in the paint job.  1 air bub2 air bub

MM is filling the air pockets, but that requires re-glassing, time for curing, re-sand, wash, repeat, etc.

I was pleased to see how MM was able to significantly improve the fitting of the doors and hood.  The lines/gaps are looking great.

In the meantime, I prepped the remaining metal parts (door sills, wheel wells/splash guards, etc.) by cleaning and coating with Sharkhide.  I also found someone to bind the edges of the carpet that will sit on the hatch floor area (so I can flip it up for access, without it fraying).

I also took the opportunity to re-do the floor of my garage.  I used Racedeck brand garage floor tiles.  I designed a checkered pattern with a blue outline for each bay.  The whole tiles go down fairly easy, snapping together.  The partial tiles take a little time to measure and cut, but overall a fairly easy project (and not much more expensive than the high end garage floor paints if you do the proper acid-wash etching first).

10 Race Deck

I hope to see primer and paint on the Coupe in August, and have her back in the garage for final assembly some time in September.

 

Off to Paint (June 25, 2016)

Work in May and June has been geared towards getting the car ready to go to the body/paint shop.  There will still be work to do after the paint (re-assemble all exterior pieces, prep and install firewall extensions, wheel wells, door sills, carpeting, etc.).  However, getting the car to paint is a major milestone.

I completed the metal duct work in front of the radiator.  FFR provided no guidance regarding how to fit these pieces.  I may want to add a fan shroud later to maximize air flow through the radiator.1 radiator metal2 radiator metal

With the hood up, engine is looking splendid.  Sounds great too.

I set the rear hatch glass in place.  My son Zach helped adjust the u-bolt to catch the lock handle.  The FFR manual says to bolt the struts to a chassis tube.  But that is difficult because at this stage the tube is hidden under the fiberglass body and the metal sides of the hatch.

I fitted the headlight covers.  The plexi provided is over-sized and I spent an entire day gently grinding down the edges to make the fit as nice as possible.  Here the covers are fitted with clecos.  I will have to remove them before paint.

I removed the body (which required removing the side pipes, and seats) so I could do a few more things:  added weather-stripping where the body sits on the chassis, added Dynamat sound barrier to the ceiling (to be covered by the headliner), and completed the metal around the pedal box.  I cut a large hole on the top panel for future access to the pedals, brake cylinders, throttle cable, clutch cable, etc. and I created a panel cover door.  The firewall extension metal will overlap the access door, but I plan to install the firewall extensions with screws to make that removable also. 12 ftbx metal

While the body was off I took apart the dash, removing all gauges and switches, in order to prep the dash pieces for powder-coating..  11.1 dash11 dash

I took the dash pieces to Bonehead Performance in Warrington, PA and selected a flat black wrinkle coating. Here is the dash and switch panel re-assembled after powder-coating.  17 dash

I also took the side-pipes to Bonehead Performance and had them ceramic coated in a silver paint.  The traditional Coupe look is white for the pipes, but I went with silver as a matter of personal choice.

Mark Dougherty (The Travelling Builder) spent a day with me.  We connected the fuel filler neck to the Le Mans gas cap.  FFR provides a metal pipe from the tank which is too long.  I removed it from the fuel tank and we cut it down with the angle grinder.  Then we tossed the straight piece of fuel hose provided by FFR and used a 45 degree one instead.  (Thanks to a post on the forum suggesting the 45 degree hose.)  We also worked through 50% of the A/C system and hoses.  Still more to do there.  One last look at the Coupe before I take it apart for paint.  side-18 drive

Finally, I loaded the coupe on a Uhaul trailer and pulled it to Metal Morphous in North Haven CT.  Here is the Coupe riding my tail.  19 mirror

Ron at MM will do the final fitting of the body, hood and doors, prep and paint (going with the traditional Guardsman Blue with white rally stripes and gumballs),  and will install the spoiler and scoops.  I also asked Ron to install the headliner after paint and before he puts the body back on.  That should save me some pain.

20 at MM

Once Ron has the body and hood off for prep and paint, I may try to bring the chassis back to PA so I can finish off the A/C system, and do a few other things (i.e. install the carpeting, add padding to the roll cage, etc.)  If so, I will have to make another trip to bring the chassis back to him when he is ready to re-install the painted body pieces.

In the meantime, I have some A/C fitting to order, and I need to get some sections of the carpet bound.  I am also using the opportunity to upgrade my garage floor to Racedeck tiles.  Until next update, peace out, or drop the mic, or something trendy.